Give a watering can a sprinkle of blooms and butterflies using napkins with decoupage! This easy and fun technique works on any surface that you want to refresh and give a spring or blooming makeover.
Happy Thursday! I hope you’re staying sane while sheltering at home. I’ve found that having some projects to keep your mind and hands busy helps. We’ve been busy gardening and I’ve been puttering around the Potting Shed.
Gardening is good for the soul and you get flowers. . .🌼
With extra time on my hands these days I decided to give a couple of watering cans a makeover using napkins, adding some blooms with a sprinkling of birds and butterflies! I found my napkins at Tuesday Morning back in February with the intention of using them to decorate Easter eggs, but never got around to it. Maybe next year as I only used 2 napkins per package.
If you’re a reader of my blog, you know I have a *slight* watering can addiction. ;-) I had two watering cans that were in a sad state and decided to give them a fresh coat of paint before I began decoupaging, using leftover green chalk paint from a couple of garden projects. On the watering can on the right, I sanded the rusty areas before painting, removing any loose paint chips.
A toothpick was an easy way to keep the holes on the rose of the watering cans from sealing closed from the paint. If painting first, allow your project to thoroughly dry at least 24 hours before decoupaging.
In addition to napkins, you’ll need some Mod Podge which will act as a glue and sealer. I used a matte Mod Podge as the gloss Mod Podge would highlight the wrinkles and my decoupaging imperfections.
Some napkins are 2-ply and others are 3-ply, mine were 3-ply. To start, separate the napkin layers and discard the white layers so you’re working with the top patterned layer. If you have trouble separating the plys, cut or tear your designs first which will make it easier to separate them.
I started cutting the napkins and decided I liked the look of the torn edges better and found it much quicker than cutting. The torn edges also made it easier to separate the layers and remove the middle ply of the napkins that were really stuck.
It’s been years since I decoupaged anything! I found a couple of helpful tips and videos on YouTube to help reduce the wrinkles.
One method is lay your napkin face down on a piece of plastic wrap. I started with plastic wrap and then switched to a clear binder sleeve I had that wasn’t as flimsy. Take a smooth bristle brush and gently brush enough water on your napkin design to carefully smooth out the wrinkles.
Flip the plastic over and place your design where you want it.
Transfer the wet napkin by gently peeling it off the plastic and the onto the surface of the watering can.
You don’t have to worry about placing a layer of Mod Podge on the can first using this method. The wet tissue of the napkin clings to the surface of the can and the Mod Podge will transfer through the thin tissue when brushed on top, gluing it to the can. I only used this method for the larger design areas of the napkins that I wanted to keep whole and intact.
With the smaller pieces of napkins, I brushed the Mod Podge onto the area of the can where I wanted it and then applied the pieces onto the Mod Podged area.
I covered the sides and tops of the watering cans to create a collage with the torn pieces of napkins. Layout your design on the surface of your project beforehand so you have an idea where you want them to go before applying the Mod Podge.
There’s a bit a learning curve if you haven’t done this before or if it’s been a while since you’ve decoupaged. The best tip I have is to take your time and not rush. . .easier to do these days. ;-) Smaller pieces are easier to apply and keep wrinkle free. Smooth your torn pieces of napkin out from the center to help reduce wrinkles. Allow the undercoat of the Mod Podge to dry at least 15 minutes before applying a top coat. I switched from a foam brush to a smooth bristle brush which reduced tearing and didn’t ‘grab’ the napkin like the foam brush did.
If you tear your napkin while brushing, don’t panic. Unwrinkle it as gently as possible with your brush or remove the piece while still wet and start over. If you’re covering the surface completely as a collage, allow it to dry, then cover and patch your tear with another piece of napkin.
After your design is complete, apply a top coat of Mod Podge to the entire surface and allow to dry. Brush it on using thin, even strokes. Allow it to dry completely (about an hour) before applying a second coat. For additional durability, spray your finished project with an acrylic sealer and to reduce any tackiness.
You can use this technique to decorate any surface…flower pots, birdhouses, furniture. . . the possibilities are endless! I plan on using my watering cans decoratively indoors but if you plan to use your decoupaged item outdoors, remember to spray with several coats of acrylic sealer to protect it from the elements.
A craft project that keeps your hands and mind busy while you’re stuck at home can be good for your mental health!
I’m happy to be part of a Creative Craft Blog Hop. Visit my blogging friends to find more craft projects at the links below:
Celebrate & Decorate
At Home With Jemma
Hearth and Vine
My Hubbard Home
My Thrift Store Addiction
Home is Where the Boat Is
The Painted Apron
Chas’ Crazy Creations
Harbour Breeze Home
My Family Thyme
Sustain My Craft Habit
Birdz of a Feather
Decorate and More with Tip
Our Crafty Mom
White Arrows Home
Create With Cynthia
Calypso in the Country
B4 and Afters
Purple Hues and Me
Bluesky at Home
Faeries & Fauna Craft Co.
Elle Marie Home